Suzhou Electric Appliance Research Institute
期刊號： CN32-1800/TM| ISSN1007-3175

Article retrieval

文章檢索

首頁 >> 文章檢索 >> 往年索引

電連接器插拔應力下接觸電阻分析

來源：電工電氣發(fā)布時間：2022-01-20 13:20 瀏覽次數：589

電連接器插拔應力下接觸電阻分析

丁睿1，倪俊芳1，黃世彬2
(1 蘇州大學 機電工程學院，江蘇 蘇州 215021；
2 蘇州瑞可達連接系統股份有限公司，江蘇 蘇州 215021)
 
    摘 要：電連接器是通過壓力接觸的連接方式，達到順利的電氣接通。為研究電連接器在插拔應力下接觸電阻特性，基于接觸電阻理論，采用 ANSYS 軟件對電連接器進行模擬插拔研究，并采用 COMSOL 軟件對接觸電阻進行仿真分析。通過實驗對比得到電連接器接插件插拔時接觸壓力與接觸電阻呈反比關系，插拔次數與接觸電阻基本呈正比關系，但不會在短時間內對接觸電阻有較大影響。
    關鍵詞：電連接器；插拔；接觸電阻；仿真分析
    中圖分類號：TM503+.5     文獻標識碼：A     文章編號：1007-3175(2022)01-0028-04
 
Analysis of Contact Resistance of Electrical
Connector Under Plugging Stress
 
DING Rui1, NI Jun-fang1, HUANG Shi-bin2
（1 School of Mechanical and Electrical Engineering, Soochow University, Suzhou 215021, China;
2 Suzhou Recodeal Interconnect System Co., Ltd, Suzhou 215021, China）
 
    Abstract: The electrical connector is connected by pressure contact to achieve a smooth electrical connection. To study the contact resistance characteristics of the electrical connector under plugging stress, ANSYS is used to simulate the plug-in analysis of the electrical connector, and COMSOL is used to simulate the contact resistance based on the contact resistance theory. The result shows that the contact pressure is inversely proportional to the contact resistance when the electrical connector is plugged in and out; the plugging times are proportional to the contact resistance. However, it would not have an obvious impact on the contact resistance in a short time whenever the electrical connector is plugged in and out.
    Key words: electrical connector; plugging; contact resistance; simulation analysis
 
參考文獻
[1] 駱燕燕， 武雄偉， 田亞超， 等. 沖擊環(huán)境下電連接器接觸性能研究[J] . 工程設計學報，2018，25(1) ：110-117.
[2] ITO T, OGIHARA S, HATTORIY Y.Observation of structural transition of tin plated fretting contacts using FIB-SEM[J].IEICE Transactions on Electronics，2011，94(9)：1350-1355.
[3] ITO T, NOMURA Y, HATTORIY Y.Observation of tin plated fretting contacts using FIBSEM[J].IEICE Transactions on Electronics，2010，93(9)：1452-1455.
[4] 任萬濱，崔黎，翟國富，等. 電連接器接觸件插拔特性與接觸電阻的仿真分析[J] . 機電元件，2012，6(3) ：40-44.
[5] 范建平，許彬彬，胥進道，等. 電連接器接觸件的分離力仿真與優(yōu)化設計[J] . 機電元件，2017，11(4) ：9-12.
[6] ABDI R El, BENJEMAA N.Experimental and analytical studies of the connector insertion phase[J].IEEE Transactions on Components and Packaging Technologies，2008，31(4) ：751-758.
[7] SAWCHYN I, SPROLES E S.Optimizing force and geometry parameters in design of reduced insertion force connectors[J].IEEE Transactions on Components, Hybrids and Manufacturing Technology，1992，15(6) ：1025-1033.
[8] COOPER M G, MIKIC B B, YAVANOVICH M M.Thermal contact conductance[J].International Journal of Heat Mass Transfer，1969，12(3) ：279-300.
[9] 賀占蜀，張遠西，王培卓，等. 電連接器接觸件的插拔和溫升特性[J].華南理工大學學報(自然科學版)，2017，45(4) ：59-65.
[10]FAN Janping, XU Binbin, XU Jindao,et al.Separation force simulation and optimization design of contact for electrical connector[J].Electromechanical Components，2017，11(4) ：9-12.